How to Install Replacement Bulbs for Downlights

by:DGT Lighting     2020-02-20
Embedded Lighting can be found in many areas of the home, also known as downlights.There are many decorations that change the way light is used from downlights.Openings and baffle decorations for mission lighting and area lighting.Eye trimming allows you to direct the light to your favorite picture hanging on the wall.The wet position decoration allows you to install the lights directly above the shower, and some decorations can even clean the walls under soft lighting.Unfortunately with these different decorations, it can be a bit complicated to install a replacement bulb.Turn off the baffles, eyeballs, or turn on the light switch that decorated the downlight.Place a ladder under the bulb you need to replace.Let the bulb cool for 20 to 30 minutes if it still works.Before removing the bulb, adjust the eye trim until the bulb goes straight down to the floor.If you can\'t catch the body of the bulb, turn the bulb counter-clockwise with your fingertips.If you are unable to turn the bulb with your fingertips, please use adhesive tape.Cut a 6-to 8-Inch-length tape and stick both ends of the tape to the surface of the bulb, and the tape hangs from the surface of the bulb at U-shape.Grab the outside of the tape and squeeze the tape together to form a handle.Use the tape \"handle\" to turn the bulb counter-clockwise.Remove the bulb and take it to the home improvement center to buy a replacement.Carry the old bulb with you when purchasing a replacement product, make sure you will purchase the correct bulb for the downlight.Insert the new downlight into the socket and turn clockwise.Turn on the light switch.Turn off the light switch to your damp position.Place a ladder under the bulb you need to replace.Let the bulb behind the trim cool for 20 to 30 minutes if needed.Grab the outside edge of the wet position trim with your fingertips.Pull the decoration from the ceiling until the decoration stops.Squeeze Two twist springs with your fingers and loosen the trim from the bracket inside the downlight housing.Grab the bulb by hand, turn counter-clockwise and remove it from the socket of the downlight housing.Bring a light bulb when you visit home improvement center to buy the right replacement.Don\'t guess your bulb, especially when replacing it in a damp place.The wrong bulb can cause the housing to overheat and cause the bulb to cycle behind the decoration.Insert the replacement bulb into the housing socket.Turn the bulb clockwise until it stops.Squeeze the wet position with your finger to decorate the two twist springs on it.Put the spring back into the bracket inside the downlight housing.Push the decoration to the ceiling with your hand and turn on the light switch.Turn off the light switch to lowVoltage downlight.Place a ladder under the downlight you need to replace.Let the low-The voltage bulb cools for 20 to 30 minutes if needed.Grab the outside edge of the lowFingertip voltage regulation.Pull the trim from the ceiling until it stops.Squeeze Two twist springs with your fingers on each side of the lowerVoltage regulation releases it and the bulb from the holder inside the downlight housing.Pull the low-Light bulb from low voltagevoltage socket.The low-The voltage bulb is connected to the socket with two pins.Slip the low-The voltage bulb below the spring clip keeps it in the decoration.Take the low-Go to the home improvement store with you to buy the replacement voltage bulb.Make sure the bulb you purchased is the exact wattage and size.In addition, compare the pins on the back of the original bulb with the replacement bulb.Make sure the width is exactly the same between the pins.Check the wattage of the bulb to make sure it is 12 V instead of 120 V as these bulbs are almost the same.Do not try to bend the pins on the replacement bulb to fit your socket.Insert the replacement bulb under the spring clip and fix it in the decoration.Align the bulb pin with the two holes on the socket.Press the socket on the bulb.Squeeze the two twist springs on the trim with your fingers.Insert the spring into the bracket inside the downlight housing.Push the low-Trim the voltage on the ceiling with your hand and turn on the light switch.
Custom message
Chat Online
Chat Online
Chat Online inputting...